COB LED-Stripe 24 Vdc IP 67 In contrast to conventional LED stripes, no individual light points are visible in COB LED stripes, as the LEDs are packed closely together to create a continuous, absolutely uniform band of light. LED COB stripes are a type of LED strip light based on chip-on-board (COB) Technology. With the COB LED strips from PUR-LED you get a continuous light band without light-dark transition similar to neon lighting due to a high number of LEDs per metre (here with a high density of 480 LEDs/m). The COB LED stripe has an IP67 protection class and is suitable for wet and/or outdoor use. The COB LED stripes can be used like normal LED strips, but offer the advantage of a very homogeneous illumination. The LED COB stripe RGB is currently available in a length of 5 metres. Advantages of the COB LED stripes IP 67: -homogeneous illumination - no individual LEDs visible absolutely uniform light pattern high Efficiency flexible and easy to bend 480 LED chips per metre protection class IP 67 for outdoor or wet areas Application examples for COB LED strips: logos and lettering with luminous effect for outdoor use for bathrooms, saunas or other wet Areas homogeneous line light, also in very flat aluminium profiles contour lighting, also on curved lines continuous, narrow accent or orientation light Technical data COB LED strip 24 Vdc IP 67:   Electrical data Rated voltage: 24 Vdc Rated current: 0,4 A/m Rated power: 10 W/m Efficiency: 70 lm/W Energy Efficiency class: G Light technical data luminous flux: 700 lm/m light color: neutralwhite color temperature: 4.000 K color Rendering index RA: 90 beam angle: 120° dimmable via PWM (s. Datasheet) Lifetime & ignition time rated life: 30.000h ignition time: <0,5s starting time:  immediate Temperatures Operating temperature: 55°C measured at TC Point Storage temperature: -15 to +40°C Dimensions length: 1.000-5.000 mm width: 11 mm height: 4 mm pitch: 50 mm Please refer to our data sheet under Downloads for further technical details and safety instructions.

CASAMBI interface configurable to " DMX ". For convenient control of operating devices and luminaires with DMX signal Input Controlled by a smart device (Apple, Android) with the CASAMBI app Configure different control modes (1..8 channels, TW, D2W, RGB(W)), before  coupling into the network: Change profile Gateway is not required, but setup is possible Integrated antenna / external antenna, do not cover Connection cable for primary side connection   Technical data:   Item number, Installation housing       808899 Type Installation housing IBTDMX8 Supply input 12....36VDC Radio signal 2,4..2,483 GHz; 4 dBmType Installation housing Signal output DMX max. 120mA Ambient temperature (ta) -20.. +45 °C Max. desisgn temperature (tc) 55 °C Dimensions 61 x 29 x23 mm ( without cable)   You can conveniently control all settings via the free CASAMBI app (Apple / Android): CASAMBI QR Code and links (here directly to the download) Casambi app in the app store Casambi app for Android For further information and connection diagrams of the Casambi interface, please refer to the data sheet (in the download tab).  

DALI converter for the converting of 0-10V analog signals to DALI With the compact interface module by Lunatone, the converting of analog signals (0-10V) into digital DALI signals happens easily. Choose your preferred model of the DALI converter from the variants with resp. without OFF-function and a dimming range of either 1-100% or 10-100% now. Overview of the specifications of the DALI converter: The read in 0-10V voltage is issued on the DALI-subcircuit via broadcast . A changing of the 0-10V input voltage (>1%) is used as event trigger. A linear 100k-potentiometer can be directly connected to the 0-10V to DALI converter.. The module is supplied by a 12-24V power supply or a DALI-circuit, at any polarity. Compact interface module for the converting of 0-10V control signals into DALI (Direct Arc Power Level). Integrated bus supply for the DALI-subcircuit with up to 4 standard-DALI charges (10mA), expansion for up to 64 charges is possible with a DALI-expander. The standart application for the 0- 10V to DALI converter is therefore the direct control off up to 4 DALI-EVGs with a 0-10V control unit. A galvanic isolation between DALI-output (10mA) and 0-10V input resp. 24V-supply can be realised with a DALI-expander Various variants for different output cable areas, as well as switch-on and switch-off conducts are available.     Technical data:   Type 0-10V / DALI converter Function: converter Typical electricity demand: 4,1mA + electricity demand for the DALI subcircuit Output: DALI, Imax = 10 mA Power supply: 12 V - 24 V at any polarity Input: 0 - 10 V Protection type: IP20 Wirelength to the 0 - 10 V control unit: 50 cm Connection wire section: 0,5 - 1,5 mm2 Temperature: 0 °C - 50 °C Dimensions (LxWxH): ca. 40x28x15 mm These variants with the following specifications are avialable:   Active and passive input available (universal use and replace the following versions gradually): with OFF-function (1%-100%): 86468352-001 with OFF-function (10%-100%): 86468352-010 without OFF-function (1%-100%): 86468352-101 without OFF-function (10%-100%): 86468352-110   Active input (module provides the power supply, direct connection of a (linear) 100k?-potentiometer is possible, phaseout): with OFF-Funktion (1%-100%): 86468352-001-A with OFF-Funktion (10%-100%): 86468352-010-A without OFF-Funktion (1%-100%): 86468352-101-A without OFF-Funktion (10%-100%): 86468352-110-A Passive input (the module provides no voltage, suitable for the control of  a 0-10V analog signal, phaseout): with OFF-function (1%-100%): 86468352-001-P with OFF-function (10%-100%): 86468352-010-P without OFF-function (1%-100%): 86468352-101-P without OFF-function (10%-100%): 86468352-110-P

For the implementation of 0-10V control on DALI with integrated DALI PSThe compact interface module converts 0-10V control signals into DALI dimming values. With this module you can choose from different dimming characteristics. The converter has a passive and active 0-10V input and can supply up to 10 standard DALI loads.The integrated power supply of the interface is achieved by changing the 0-10V input voltage. This changed voltage is less than 1%. The module is supplied with 12-24V.By inserting a DALI expander you can achieve a galvanic isolation between the ballasts connected to the DALI output and the 0-10V input.Overview 0-10V to DALI Converter 30mA: Compact interface module for the conversion of 0-10V control signals to DALI dim levels The interface module provides a 30mA DALI power supply for up to 10 standard DALI ballasts, up to 64 ballasts controllable with the help of a DALI-Expander Passive and active 0-10V input The converted value is sent broadcast on the DALI subnet A change in the 0-10V input voltage signal (>1%) is used as trigger event The interface module requires a 12-24V power supply Easy set up of the dim characteristic with the help of jumpers A galvanic isolation between the ballasts connected to the DALI-output (30mA) and the 0-10V signal input (and 24V supply input) can be realised with the help of a DALI-expander Technical data for 86468352-HS: Supply voltage: 12V-24V Typ. current consumption: 4mA + current for DALI output Input: 0-10V, passive oder active Output: DALI Imax=30 mA Function: signal converter, selection of dim characteristic with jumper Mechanical data: Ambient temperature: -20°C to +60°C Protection class: IP20 Maximum connecting wire cross section : 0,5 - 2,5 mm² Mounting: DIN rail Dimensions: 98 x 17.5 x 56 mm More information about this product can be found in the data sheet under the Download tab.

For connecting two waterproof LED strips 12Vdc / 24Vdc For this, this line must be connected to the LED technology. E.g. with a waterproof connection box. 2-wire supply with DC plug Technical data:Typ: DC connector supply linetransparent waterproof jacketsolderable cable endsVoltage: 24Vdc max.Lenght: 0,5m Delivery scope: 1x 2-core supply cable, waterproof coated, with DC connector 0.5m

For connecting two waterproof LED strips 12Vdc / 24Vdc 2-wire supply with DC socket Technical data:Type: DC socket supply linetransparent waterproof jacketsolderable cable endsVoltage: 24Vdc max.Length: 0,5m Delivery scope: 1x 2-core cable, waterproof sheathed, with DC socket 0.5m

1-channel LED 1-10V Dimmer The 1-channel LED 1-10V PWM dimmer, 12-36VDC, 1x8A from PUR-LED with Analog input for electronic dimmers. The search for the ideal constant voltage source with 1-10V is over. With this 1-10V dimmer the system can be extended easily and reliably. Details on the wiring of the 1-channel 1-10VLED dimmer can be found in the data sheet. Technical data: Power supply: 12-36VDC Input signal: 1-10V active voltage Output voltage: 1 x 12-36VDC Output current: max. 8A Power output: 96W @ 12VDC 192W @ 24VDC 192W @ 36VDC Dimming function: 0-100% Temperature range: -20 - + 50°C Dimensions (LxWxH) in mm: 100 x 38 x 20