wDALI Relay 8A permanent, 80A Inrush, built in

DALI button switch cross or as WDALI-Set with ReceiverRadio control module for DALI circuits with four freely programmable buttons.The wDALI switch is a DALI control module, which is connected wireless to the DALI bus. The battery operated switch can be installed at every place without any installation effort. Destination address, switching characteristic and DALI commands can be assigned To every button of the wDALI switch. The following DALI commands are available for this purpose: dim up, dim down, off, recall min., recall max., goto scene 1-16, direct arcpower ...%, mask and predefined macros. Product specifications DALI control module with 4 buttons Possibility of sending DALI commands to single addresses (0-63), groups (0-15), and broadcasts As switching function different buttons (short/long button push), switching buttons, switches etc. can be chosen Memory function for brightness with the help of macros 2 different fabrication settings are possible The wDALI switch offers the possibility to control components of the DALI circuit, without the operating device being physically connected to the DALI circuit. The wDALI switch contains of two components, an arbitrarily placeable operating device (sender unit) and a receiving unit, which is connected to the DALI bus The receiver of the DALI switch is supplied through the DALI line, there is no additional connection needed Configurable power up function, this means automatic sending of a command after a power interruption The wDALI switch can instantly used for the control of a DALI circuit with the fabrication settings Adjustments and changing of the configuration through the DALI bus with help of the DALI cockpit software Every button can be assigned to 4 destination addresses, switching functions and DALI commands  The following DALI commands are available for this purpose: up, down, off, recall min/max, goto scene 1-16, direct arcpower in % and macros DALI DT8 support for the control of colour temperature of luminaires through appropriate macros Multiple wDALI switch can be used in the same DALI circuit The operating unit of the wDALI switch is designed as wall switch and can be placed freely within the receiving range of the receiver Technical data Colour: white/black Supply: Battery resp. via DALI-Bus typ. current consumption: 2 mA Output: DALI Function: programmable Frequency band: 2,4Ghz Receiving range: up to 300 m Dimensions operating unit (W x H x D): 82x82x8,5 mm Expectable battery life of the operating unit: 6 years Dimensions Receiver (W x H x D): 35 mm x 28 mm x 15 mm Temperature: -10 °C - 50 °C Protection type: IP54 Connecting wire section: 0,5 - 1,5 mm2

Wireless DALI radio control multi-control with receiver and transmitter The wDALI MC is a DALI control module, which is linked wireless to the DALI bus. The battery-operated transmission module of the DALI radio control has 4 switch inputs and can be mounted to the DALI bus at every desired place within the reception radius of the receiving unit. The set contains the transmitter 89453848 as well as the receiver 86459534. Destination address, switching characteristics, and DALI commands can be assigned to every input of the wDALI MC. The following DALI-commands are available for this purpose: dim up dim down off recall min. recall max. goto scene 1-16 direct arcpower ...% mask and predefined macros. Attention, when re-ordering a single receiver or transmitter module, please state the SN of the device to be connected.

Lunatone DALI radio control with receiver unit Choose your favorite color for the DALI remote control and control your DALI center wirelessly and comfortably with the DALI remote control from Lunatone. Using the DALI cockpit, it is possible to configure each of the 12 buttons of the wDALI Remote so that DALI commands are sent to one or several desired destination addresses or groups at the press of a button. DALI remote control single, or in a set with receiver available. Receiver available separately on request. Product features Adaptation and modification of the configuration via the DALI bus using the DALI Cockpit software Each key can be assigned up to 4 destination addresses, switching functions and DALI command (s) The wDALI radio remote control consists of two components, an arbitrary placeable operating device (transmitting unit) and a receiving unit, which is connected to the DALI bus The remote control can be used immediately with the factory setting to control a DALI circuit. Two different factory settings possible The control unit of the wDALI Remote is designed as a typical remote control and can be used from any location within the receiver's reception range. DALI control module with 12 buttons Ability to send DALI commands to individual addresses (0-63), groups (0-15), and broadcast The switch function can be selected between different buttons (short / long button press), change buttons, switches, etc. The following DALI commands are available: up, down, off, recall min / max, goto scene 1-16, direct arc power in% and macros The receiver of the wDALI-Remote is supplied via the DALI line, no additional connection is necessary DALI DT8 Support for controlling the color temperature of luminaires with appropriate macros Memory function for brightness using special macros The wDALI-Remote offers the possibility of controlling components of a DALI circuit via radio Configurable "Power Up" function, ie automatic sending of a command after a power interruption Several wDALI Remote can be used to control the same DALI circuit Technical specifications Color control panel: white / black (optional) Supply: from DALI bus Typical current consumption: 3.8 mA Output: DALI Function: programmable Frequency band: 2.4 GHz Receiving radius: up to 300 m Dimensions of control panel (W x H x D): 140 mm x 52 mm x 10 mm Approximate battery life Control panel: 6 years Dimensions of receiver (W x H x D): 59 mm x 33 mm x 15 mm Temperature: -10 degrees C to +50 degrees C Protection class: IP20 Connection wires cross section: 0.5-1.5 mm²

Wireless switching relay for DALI radio control with transmitter and receiver The wDALI RM8 is a DALI control module, which is wirelessly connected to the DALI bus. This enables the integration of spatially separated switchable loads such as floor lamps and outdoor luminaires into the DALI system. The loads can be switched on and off with DALI commands.   Overview Wireless DALI-line espansion for ballasts with PWM control input 2 components: a transmitter unit connected to the DALI-line and a receiver module with 0-10V PWM output and relay Integrated relay for switching ballast supply Advantage of fail-safe digital signal data communication compared to types with analog output voltage, suitable for electronic ballast with PWM control input (e.g. Meanwell HLG, HLN, NPF or LPF series) Transformation of DALI light level into PWM output signal from 0% to 100% DALI DT5: selection of linear or logarithmic dimming curve DALI DT5: output range selection (0-100% / 10-100% PWM) Maximum output current of 1mA (current sink) The relay contact depends on the light level, at 0 the relay is opened, at any other value it is closed The transmitter unit is powered directly by the DALI-line, the receiver is powered by mains Configuration via DALI-Cockpit software too   Electrical data transmitter   Supply via DALI Bus typ. current consumption 3,8 mA Input DALI Power on behaviour programmable, here the Power On is the return of the DALI-line supply voltage Frequency-range 2,5 GHz Technical data transmitter   Ambient temperature -10°C to + 50°C Protection class IP20 Connection wire cross section max. 1,5mm² Mounting black box Dimensions L x B x H 59 x 33 x 15 mm   Electrical data switch relay   Supply 210-250V AC / 50-60Hz Rated load 1000VA max. switching current  8A max. power on current 80A Relay contact 1 on / off, max. 30000 operations at nominal load resistive, max. Switching frequency 1Hz Frequency-range 2,4Ghz Technical data switch relay   Ambient temperature 0°C to + 45°C Protection class IP20 Connection wire cross section max. 1,5mm² Mounting black box Dimensions L x B x H 59 x 33 x 15 mm For further information on the wDALI RM8 radio switching relay, please refer to the data sheet in the Download tab.

DALI-Transmitter from LunatoneModule to wirelessly tether spatially divided DALI ballast to a DALI system. The GR transmitter, connected to the DALI line, wirelessly sends DALI commands to one or more receivers. The wDALI Receiver PS20 has got an integrated 20mA bus supply for the DALI subsystem. Using the dial on the back of the receiver an address for the DALI subsystem can be selected. The devices in the subsystem can be controlled via broadcast or the set group address.We also offer you the wDALI GR Receiver PS20 (86459587-GRRPS) from Lunatone. Overview: Module for the wireless integration of spatially separated DALI ballasts in a DALI system For the wireless connection at least two components are required: one transmitter and one receiver Range of wireless connection up to 300m outdoors, indoors typically 10m-20m Easy group assignment to G0...G15 with the help of a rotary group selector on the receiver: all commands sent to the selected group or broadcast are forwarded to the receiver subnet The commands are sent broadcast on the subnet The transmitter is supplied from the DALI-line, the receiver is supplied by mains and provides a 20mA DALI bus power supply for the subnet A DALI-Expander can be used on the subnet for higher DALI loads A transmitter can control finitely many DALI subnets with a separate transceiver for each subnet Double DALI terminals ? the DALI signal line is connected through Electrical data  transmitter   Supply via DALI Bus typ. current consumption 3,8 mA Input DALI Function Forwarding of DALI-commands via RF-connection RF range 2,4 GHz Technical data transmitter   Ambient temperature -10°C to + 50°C Protection class IP20 Connection wire cross section max. 1,5mm² Mounting Back box Dimensions L x W x H 59 x 33 x 15 mmMore information about this product can be found in the data sheet in the Download tab.

DALI-Receiver from Lunatone Module to wirelessly tether spatially divided DALI ballast to a DALI system. The GR transmitter, connected to the DALI line, wirelessly sends DALI commands to one or more receivers. The wDALI Receiver PS20 has got an integrated 20mA bus supply for the DALI subsystem. Using the dial on the back of the receiver an address for the DALI subsystem can be selected. The devices in the subsystem can be controlled via broadcast or the set group address. We also offer the wDALI GR Transmitter (86459587-GRTM) from Lunatone.   Overview: Module for the wireless integration of spatially separated DALI ballasts in a DALI system For the wireless connection at least two components are required: one transmitter and one receiver Range of wireless connection up to 300m outdoors, indoors typically 10m-20m Easy group assignment to G0...G15 with the help of a rotary group selector on the receiver: all commands sent to the selected group or broadcast are forwarded to the receiver subnet The commands are sent broadcast on the subnet The transmitter is supplied from the DALI-line, the receiver is supplied by mains and provides a 20mA DALI bus power supply for the subnet A DALI-Expander can be used on the subnet for higher DALI loads A transmitter can control finitely many DALI subnets with a separate transceiver for each subnet Double DALI terminals – the DALI signal line is connected through Electrical data receiver   Supply 210-250V AC / 50-60Hz Output DALI, 20mA (for up to 10 DALI ballasts) Function Receiving DALI-commands via RF Group selection with rotary switch Broadcast-forwarding of commands to selected group on DALI subnet RF range 2,4 GHz Technical data receiver   Ambient temperature -10°C bis + 50°C Protection class IP20 Connecting wire cross-section max. 1,5mm² Mounting Back box Dimensions L x W x H 59 x 33 x 15 mm More information about this product can be found in the data sheet in the Download tab.