DALI SC/SC-A Scene Control Module

DALI button switch cross or as WDALI-Set with ReceiverRadio control module for DALI circuits with four freely programmable buttons.The wDALI switch is a DALI control module, which is connected wireless to the DALI bus. The battery operated switch can be installed at every place without any installation effort. Destination address, switching characteristic and DALI commands can be assigned To every button of the wDALI switch. The following DALI commands are available for this purpose: dim up, dim down, off, recall min., recall max., goto scene 1-16, direct arcpower ...%, mask and predefined macros. Product specifications DALI control module with 4 buttons Possibility of sending DALI commands to single addresses (0-63), groups (0-15), and broadcasts As switching function different buttons (short/long button push), switching buttons, switches etc. can be chosen Memory function for brightness with the help of macros 2 different fabrication settings are possible The wDALI switch offers the possibility to control components of the DALI circuit, without the operating device being physically connected to the DALI circuit. The wDALI switch contains of two components, an arbitrarily placeable operating device (sender unit) and a receiving unit, which is connected to the DALI bus The receiver of the DALI switch is supplied through the DALI line, there is no additional connection needed Configurable power up function, this means automatic sending of a command after a power interruption The wDALI switch can instantly used for the control of a DALI circuit with the fabrication settings Adjustments and changing of the configuration through the DALI bus with help of the DALI cockpit software Every button can be assigned to 4 destination addresses, switching functions and DALI commands  The following DALI commands are available for this purpose: up, down, off, recall min/max, goto scene 1-16, direct arcpower in % and macros DALI DT8 support for the control of colour temperature of luminaires through appropriate macros Multiple wDALI switch can be used in the same DALI circuit The operating unit of the wDALI switch is designed as wall switch and can be placed freely within the receiving range of the receiver Technical data Colour: white/black Supply: Battery resp. via DALI-Bus typ. current consumption: 2 mA Output: DALI Function: programmable Frequency band: 2,4Ghz Receiving range: up to 300 m Dimensions operating unit (W x H x D): 82x82x8,5 mm Expectable battery life of the operating unit: 6 years Dimensions Receiver (W x H x D): 35 mm x 28 mm x 15 mm Temperature: -10 °C - 50 °C Protection type: IP54 Connecting wire section: 0,5 - 1,5 mm2

DALI RM8/RM16/RM16-DE/RM16-CEL Module for controlling a relay contact via the DALI bus DALI Relay Module RM8/16/16-DE/16-CEL provides a relay contact controllable via the DALI bus which can be used to switch constant loads of up to 1 or 2 kVA. DALI RM16 is particularly suited for high starting current peaks up to 160 A; it is equipped with a changeover contact which is used as a relay contact. The RM8 is suited for starting current peaks of up to 80 A; the relay contact is designed as a normally open contact. A special feature of the switching actuator DALI Relay Module RM8/16/16-DE/16-CEL is that it maintains the switching status of the relay in the case of a bus supply failure. Any switch-on and/or switch-off delay can be programmed via the DALI bus. Thus, loads without DALI input can be incorporated in the DALI system.   Product features Compact relay module for the direct control of 230 VAC loads via DALI Simple incorporation of loads without DALI input into a DALI circuit; the loads can be switched on and off using DALI commands Different variants available, suitable for your application requirements Possibility of configuring switch-on and switch-off delays using the parameters FADE RATE and FADE TIME DALI Cockpit is the DALI configuration tool of Lunatone which is available for free download; it can be used for configuration DALI Relay Module RM 8/16/16-DE/16-CEL is supplied by the DALI bus; no further supply required RM16 is particularly suitable for high starting current peaks up to 160 A The interface represents a bus user and can be addressed accordingly Available versions: DALI RM16 for socket installation (manufacturer's number: 86458629) V-1605098 Maximum nominal load and nominal current: 1000VA / 8A Maximum starting current peaks: 160A Relay contact type: 1 changeover contact Switching cycles at 8A/250VAC, resistive: 3x104 DALI RM8 for socket installation (manufacturer's number: 86456944 (Previous 86458675) V-1605099 Maximum nominal load and nominal current: 1000VA / 8A Maximum starting current peaks: 80A Relay contact type: 1 normally open contact Switching cycles at 8A/250VAC, resistive: 3x105 DALI RM16 for ceiling installation (manufacturer's number: 86458629-DE) V-1623447 Maximum nominal load and nominal current: 2000VA / 16A Maximum starting current peaks: 160A Relay contact type: 1 changeover contact Switching cycles at 16A/250VAC, resistive: 3x104 DALI RM16 with Wieland plug-in contacts (manufacturer's number: 86458629-CEL) V-1626583 Maximum nominal load and nominal current: 2000VA / 16A Maximum starting current peaks: 160A Relay contact type: 1 normally open contact Switching cycles at 16A/250VAC, resistive: 3x104 Other technical data: Power supply: via DALI-Bus Typical current consumption: 2,7mA Inputs: DALI Used DALI addresses: 1 Switch-on / switch-off voltage relay contact: 250 VAC / 400 VAC Maximum permissible switch frequency: 1Hz Temperature: 0 °C - 45 °C Protection class: IP20 Connecting wires profile: 0,5 - 1,5 mm2 History (Previous) Item RM8 86458675 from Article 86456944

DALI relay contact RM module 24034702 for controlling via the DALI bus The DALI relay contact RM module provides a relay contact that can be controlled via the DALI bus and can be used for switching lights and small loads or for controlling contactors. Loads without DALI input can be integrated into the DALI system in this way.   Product characteristics: Compact relay module for controlling a standard contactor or load via DALI Easy integration of loads without DALI input into a DALI circuit; the loads can be switched on and off via DALI commands Switch-on and switch-off points can be configured using the parameters MIN LEVEL, MAX LEVEL, FADE RATE and FADE TIME. The DALI-Cockpit is a free DALI configuration tool from Lunatone available for configuration download The DALI RM is supplied via the DALI bus Loads may only be connected directly to the DALI RM if the inrush current of the load is below 6A. Otherwise a contactor must be connected in between. Alternatively, we recommend using the DALI RM8 (up to 80A inrush current) or DALI RM16 (up to 160A inrush current) modules for high inrush currents. The maximum load of a contactor coil may be connected to the DALI RM. When selecting the correct contactor, the inrush current of the contactor must also be observed; this must not exceed 6A. DC contactor coils must be equipped with freewheeling diodes   Technical Data: Supply: from DALI bus typical current consumption on DALI bus: 10 mA Inputs: DALI DALI address: 1 Output switching voltage: 250VAC/35VDC Switching current output: 4A max. Inrush current of the load: 6A Contact type: 1 changeover Mechanical life of switching cycles: 1x107 Electrical life, switching cycles (4A/250VAC, resistive): 6x104 Temperature: 0 °C - 50 °C Protection class: IP20 Cross section of connecting wires: 0.75 mm2 Length of connecting wires: 250 mm

Lunatone DALI control module Analog DALI 100 kOhm DALI control module with analog input for connecting a 100k potentiometer With the DALI 100k, the luminaires in a DALI circuit can be controlled with a 100kOhm potentiometer.   Product characteristics: Compact control module with analog input for direct connection of a 100k potentiometer The input signal is directly converted into a DALI dimming value The conversion can be triggered periodically or by a trigger A change of the input signal (>2%) is used as the event trigger for the conversion. The dimming value can be sent to individual addresses, groups and broadcast Configuration via DALI-Cockpit and DALI-USB Interface Configuration via DALI-Cockpit and DALI-USB Interface Multimaster capable, multiple modules can be installed in a DALI circuit The module can be inserted in a flush-mounted box directly behind the potentiometer The module is supplied directly via the DALI line Technical data: Supply: from DALI bus Typical current consumption: <3 mA Inputs: 100k Potentiometer Output: DALI Temperature: 0 °C - 50 °C Protection class: IP20 Connecting wires Cross section: 0.5-1.5 mm2 max. cable length push-button module: 50 cm Dimensions (L x W x H): 40 mm x 28 mm x 15 mm

DALI control module sequencer for automatic sequences DALI command sequences can be played with the DALI sequencer. Both sequential scene calls and user-defined command sequences are supported.   Product characteristics Compact control module, enables automatically running sequences Memory for up to 4 sequences A command sequence can consist of up to 19 DALI commands The module fits into a flush-mounted box Types for back box and dinrail mounting Din rail type provides 4 switching inputs for mains voltage A sequence can consist of any command sequences or scene calls If the sequencer is assigned to a group, a running sequence can also be stopped with group and broadcast commands The sequence can be executed once or cyclically Simple configuration via DALI cockpit y calling up scenes 0-3 at the sequencer address, the corresponding sequences can be started The module draws 2mA from the Dali circuit, an additional supply is not necessary Multimaster capable, multiple master modules can be installed in a DALI circuit Technical Data: Type DALI Sequencer Article number 86459582 86459582-HS Suppy via DALI- Bus typ. current consumption 2 mA Control DALI Input DALI DALI 4 switching inputs (mains voltage) Function programmierbare Sequenzen Temperatur 0 °C - 50 °C Protection class IP20 Connecting wire cross section 1.5 mm² 2.5 mm² Mounting back box dinrail, 1TE Dimensions 39,7mm x 28mm x 14mm 98mm x 17.5mm x 56mm

DALI GC/GC-A group control module Module for the control of two predefined DALI groups with a conventional light buttonThe DALI GC and GC-A are control units for the control of 2 DALI groups. With help of this compact module, light switches or buttons can send dimming and switching commands to two DALI groups.A rotary switch on the housing DALI GC/GC-A offers the possibility to preselect the DALI resp. luminaire group. The modules are installed in the flush-mounted box behind the light switches and get their supply directly from the DALI-Bus.  Product specifications The DALI GC offers in contrast to the DALI GC-A the possibility, to address luminaires and add them to groups resp. delete them. Compact control module to generate switching or dimming commands for two DALI groups With help of a rotary switch on the module housing the selection of the DALI groups that are addressed happens. The inputs can be controlled with standard buttons Multiple modules can be installed within a DALI circuit The module can be installed in a flush-mounted box or directly behind the light button The supply of the module happens directly through the DALI line and doesn't have to be connected to the grid The buttons are connected directly to the module (make potential-free contact) Technical data: Supply: via DALI bus Current consumption: 6 mA Inputs: 2 buttons single/double Outputs: DALI (broadcast) Groups: 2 of 16 (broadcast) Group selection: rotary switch Temperature: 0 °C - 50 °C Protection type: IP20 Connected wires: 0.75 mm2 Connected length: 250 mm