DALI converter for the converting of 0-10V analog signals to DALI With the compact interface module by Lunatone, the converting of analog signals (0-10V) into digital DALI signals happens easily. Choose your preferred model of the DALI converter from the variants with resp. without OFF-function and a dimming range of either 1-100% or 10-100% now. Overview of the specifications of the DALI converter: The read in 0-10V voltage is issued on the DALI-subcircuit via broadcast . A changing of the 0-10V input voltage (>1%) is used as event trigger. A linear 100k-potentiometer can be directly connected to the 0-10V to DALI converter.. The module is supplied by a 12-24V power supply or a DALI-circuit, at any polarity. Compact interface module for the converting of 0-10V control signals into DALI (Direct Arc Power Level). Integrated bus supply for the DALI-subcircuit with up to 4 standard-DALI charges (10mA), expansion for up to 64 charges is possible with a DALI-expander. The standart application for the 0- 10V to DALI converter is therefore the direct control off up to 4 DALI-EVGs with a 0-10V control unit. A galvanic isolation between DALI-output (10mA) and 0-10V input resp. 24V-supply can be realised with a DALI-expander Various variants for different output cable areas, as well as switch-on and switch-off conducts are available.     Technical data:   Type 0-10V / DALI converter Function: converter Typical electricity demand: 4,1mA + electricity demand for the DALI subcircuit Output: DALI, Imax = 10 mA Power supply: 12 V - 24 V at any polarity Input: 0 - 10 V Protection type: IP20 Wirelength to the 0 - 10 V control unit: 50 cm Connection wire section: 0,5 - 1,5 mm2 Temperature: 0 °C - 50 °C Dimensions (LxWxH): ca. 40x28x15 mm These variants with the following specifications are avialable:   Active and passive input available (universal use and replace the following versions gradually): with OFF-function (1%-100%): 86468352-001 with OFF-function (10%-100%): 86468352-010 without OFF-function (1%-100%): 86468352-101 without OFF-function (10%-100%): 86468352-110   Active input (module provides the power supply, direct connection of a (linear) 100k?-potentiometer is possible, phaseout): with OFF-Funktion (1%-100%): 86468352-001-A with OFF-Funktion (10%-100%): 86468352-010-A without OFF-Funktion (1%-100%): 86468352-101-A without OFF-Funktion (10%-100%): 86468352-110-A Passive input (the module provides no voltage, suitable for the control of  a 0-10V analog signal, phaseout): with OFF-function (1%-100%): 86468352-001-P with OFF-function (10%-100%): 86468352-010-P without OFF-function (1%-100%): 86468352-101-P without OFF-function (10%-100%): 86468352-110-P

For the implementation of 0-10V control on DALI with integrated DALI PSThe compact interface module converts 0-10V control signals into DALI dimming values. With this module you can choose from different dimming characteristics. The converter has a passive and active 0-10V input and can supply up to 10 standard DALI loads.The integrated power supply of the interface is achieved by changing the 0-10V input voltage. This changed voltage is less than 1%. The module is supplied with 12-24V.By inserting a DALI expander you can achieve a galvanic isolation between the ballasts connected to the DALI output and the 0-10V input.Overview 0-10V to DALI Converter 30mA: Compact interface module for the conversion of 0-10V control signals to DALI dim levels The interface module provides a 30mA DALI power supply for up to 10 standard DALI ballasts, up to 64 ballasts controllable with the help of a DALI-Expander Passive and active 0-10V input The converted value is sent broadcast on the DALI subnet A change in the 0-10V input voltage signal (>1%) is used as trigger event The interface module requires a 12-24V power supply Easy set up of the dim characteristic with the help of jumpers A galvanic isolation between the ballasts connected to the DALI-output (30mA) and the 0-10V signal input (and 24V supply input) can be realised with the help of a DALI-expander Technical data for 86468352-HS: Supply voltage: 12V-24V Typ. current consumption: 4mA + current for DALI output Input: 0-10V, passive oder active Output: DALI Imax=30 mA Function: signal converter, selection of dim characteristic with jumper Mechanical data: Ambient temperature: -20°C to +60°C Protection class: IP20 Maximum connecting wire cross section : 0,5 - 2,5 mm² Mounting: DIN rail Dimensions: 98 x 17.5 x 56 mm More information about this product can be found in the data sheet under the Download tab.

1Ch 0-10V LED PWM Dimmer / Booster Control Gear ED driver (CV) with one channel, can be operated as PWM Booster or Dimmer. The device operates as PWM-Booster, if PWM-signals are applied to the input (50Hz-1kHz) If operated with 100kO potentiometer or 0-10V control devices (active and passive), the device functions as Dimmer. Overview: 1 channel LED dimmer Suitable for constant voltage LED-modules Control signals: PWM (50Hz-1kHz), 100kOhm potentiometer, 0-10V voltage signal (active and passiv) Logarithmic dimming curve Analog input: connection of a 100kOhm potentiometer or a 0-10V control device (active or passive), the 0-10V input signal is transformed in a corresponding PWM output signal PWM control signal: suitable for operation with a LED-dimmer with common plus connector Supply voltage of 12V to 48V DC Maximum current: 16A Suitable for remote ceiling   Electrical data   Supplx 12VDC-48VDC Maximum input current 16A Control input PWM (50Hz-1kHz) 100kOhm potentiometer 0-10V active/passive Technical data   Expected lifetime (at Tc<=75°C) >50000h Max. connecting wire crosssection 2.5 mm² Protection class IP20 Mounting Deckeneinwurf Dimenions (LxWxH) 120mm x 30mm x 22mm RECOMMENDATION: Care should be taken on keeping cable lengths between DC power supply and dimmer as well as between dimmer and luminaires (Led-Strings) as short as possible. This kind of installation will minimize the influence of voltage drops. For further information please refer to the data sheet in the Download tab.

Multi channel DALI constant current (CC) dimmer by Lunatone Every channel of the DALI constant current dimmer has its own DALI address Configuration and control via DALI For the direct control of LED modules with current input The outputs are dimmable from 1% to 100% Different variants for 350mA per channel in a small housing, further 1000mA per channel in a big housing are available Configuration via DALI cockpit and DALI USB interface Integrated short protection The following versions are available: Two channel versions, with 2 DALI addresses each (one address per channel) Up to max. 2x 350mA output currents: 89453845-350With a collectice positive pole: 89453845-350DEWith a collectice minus pole: 89453845-350GMDEUp to max. 2x 500mA output currents: 89453845-500With a collectice positive pole: 89453845-500DEWith a collectice minus pole: 89453845-500GMDEUp to max. 2x 700mA output currents:With a collectice positive pole: 89453845-700With a collectice minus pole: 89453845-700GMUp to max. 2x 1000mA output currents: With a collectice positive pole: 89453845-1000With a collectice minus pole: 89453845-1000GM  Three channel versions, with 3 DALI addresses each (one address per channel) Up to max. 3x 350mA output currentWith a collective positive pole: 89453846-350With a collective minus pole: 89453846-350GMUp to max. 3x 500mA output currentWith a collective positive pole: 89453846-500With a collective minus pole: 89453846-500GM  Up to max. 3x 700mA output currentWith a collective minus pole: 89453846-700GM Four channel versions, with 4 DALI addresses each (one address per channel) Up to max. 4x 350mA output currentWith a collective positive pole: 89453855-350With a collective minus pole: 89453855-350GMUp to max. 4x 500mA output currentWith a collective positive pole: 89453855-500With a collective minus pole: 89453855-500GMUp to max. 4x 700mA output currentWith a collective minus pole: 89453855-700GM  Other technical data: Output voltage range: 3V-45V (with 48V supply) Supply: 12VDC-48VDC resp. 56VDC Control input: DALI Temperature: -15 °C - 50 °C resp. -20 °C - 60 °C Protection type: IP20 Condition after return: depends on the DALI settings Max. cross wire section: up to 2,5 mm² Dimensions: Check the data sheet

Multi channel DALI constant current (CC) dimmer by Lunatone Every channel of the DALI constant current dimmer has its own DALI address Configuration and control via DALI For the direct control of LED modules with current input The outputs are dimmable from 1% to 100% Different variants for 350mA per channel in a small housing, further 1000mA per channel in a big housing are available Configuration via DALI cockpit and DALI USB interface Integrated short protection The following versions are available: Two channel versions, with 2 DALI addresses each (one address per channel) Up to max. 2x 350mA output currents: 89453845-350With a collectice positive pole: 89453845-350DEWith a collectice minus pole: 89453845-350GMDEUp to max. 2x 500mA output currents: 89453845-500With a collectice positive pole: 89453845-500DEWith a collectice minus pole: 89453845-500GMDEUp to max. 2x 700mA output currents:With a collectice positive pole: 89453845-700With a collectice minus pole: 89453845-700GMUp to max. 2x 1000mA output currents: With a collectice positive pole: 89453845-1000With a collectice minus pole: 89453845-1000GM  Three channel versions, with 3 DALI addresses each (one address per channel) Up to max. 3x 350mA output currentWith a collective positive pole: 89453846-350With a collective minus pole: 89453846-350GMUp to max. 3x 500mA output currentWith a collective positive pole: 89453846-500With a collective minus pole: 89453846-500GM  Up to max. 3x 700mA output currentWith a collective minus pole: 89453846-700GM Four channel versions, with 4 DALI addresses each (one address per channel) Up to max. 4x 350mA output currentWith a collective positive pole: 89453855-350With a collective minus pole: 89453855-350GMUp to max. 4x 500mA output currentWith a collective positive pole: 89453855-500With a collective minus pole: 89453855-500GMUp to max. 4x 700mA output currentWith a collective minus pole: 89453855-700GM  Other technical data: Output voltage range: 3V-45V (with 48V supply) Supply: 12VDC-48VDC resp. 56VDC Control input: DALI Temperature: -15 °C - 50 °C resp. -20 °C - 60 °C Protection type: IP20 Condition after return: depends on the DALI settings Max. cross wire section: up to 2,5 mm² Dimensions: Check the data sheet

4-channel DALI dimmer for 12V and 24V / DT8 mode 8006504-channel LED dimmer 800650: 4-channel LED dimmer for constant voltage control only by DALI with SELV potential, 4 channels with consecutive addresses, adjustable: ?Press a button for a long time until display flashes (address of first channel). ? press right/left to set ?Press long to save or address by DALI Control. 4-channel LED dimmer DT8 808660: 4-channel DALI² DT8 LED dimmer for LEDs for constant voltage. Suitable for control via CASAMBI interfaces in DT8 mode Controlled only by DALI with SELV potential DALI Select start address (4 consecutive addresses): - press right button (0..9) long until display flashes (address of first channel) - press right / left to set - press right long to save - or addressing by DALI Control Set operating mode: - Press both buttons long until display flashes, press one button to select working mode - nn: for single-colour LED strips, all channels the same - R9: for RGBW LED bands - 7c: for Tunable White LED bands - H4: for settings via XY-coordinate - Press and hold both buttons to confirm selection Specifications of the 4-channel LED dimmers: Product No. 808660 (DT8 Version) 800650 800651 (only on request) Type DU4DA8-14-480 4-channel DALI² DT8 LED dimmer   DU4DA14-480 4-channel DALI LED Dimmer DU4DA14-768 Input voltage 12..24 VDC 12..24 VDC 12..24 VDC Output voltage 12..24 VDC 12..24 VDC 12..24 VDC Output power at 12V 4x60 W4x60 W 4x60 W 4x96 W Output power at 24V 4x120 W 4x120 W 4x192 W PWM frequency 1500 Hz 2000 Hz 2000 Hz Control current max. 2 mA 1,5 mA 1,5 mA Max. Rated temperature tc 75 °C 75 °C 75 °C Dimensions 170 x 53 x 29 mm 178x46x20 mm 170x59x29 mm For more information please refer to the data sheets in the Download-Tab.

Multi channel DALI constant current (CC) dimmer by Lunatone Every channel of the DALI constant current dimmer has its own DALI address Configuration and control via DALI For the direct control of LED modules with current input The outputs are dimmable from 1% to 100% Different variants for 350mA per channel in a small housing, further 1000mA per channel in a big housing are available Configuration via DALI cockpit and DALI USB interface Integrated short protection The following versions are available: Two channel versions, with 2 DALI addresses each (one address per channel) Up to max. 2x 350mA output currents: 89453845-350With a collectice positive pole: 89453845-350DEWith a collectice minus pole: 89453845-350GMDEUp to max. 2x 500mA output currents: 89453845-500With a collectice positive pole: 89453845-500DEWith a collectice minus pole: 89453845-500GMDEUp to max. 2x 700mA output currents:With a collectice positive pole: 89453845-700With a collectice minus pole: 89453845-700GMUp to max. 2x 1000mA output currents: With a collectice positive pole: 89453845-1000With a collectice minus pole: 89453845-1000GM  Three channel versions, with 3 DALI addresses each (one address per channel) Up to max. 3x 350mA output currentWith a collective positive pole: 89453846-350With a collective minus pole: 89453846-350GMUp to max. 3x 500mA output currentWith a collective positive pole: 89453846-500With a collective minus pole: 89453846-500GM  Up to max. 3x 700mA output currentWith a collective minus pole: 89453846-700GM Four channel versions, with 4 DALI addresses each (one address per channel) Up to max. 4x 350mA output currentWith a collective positive pole: 89453855-350With a collective minus pole: 89453855-350GMUp to max. 4x 500mA output currentWith a collective positive pole: 89453855-500With a collective minus pole: 89453855-500GMUp to max. 4x 700mA output currentWith a collective minus pole: 89453855-700GM  Other technical data: Output voltage range: 3V-45V (with 48V supply) Supply: 12VDC-48VDC resp. 56VDC Control input: DALI Temperature: -15 °C - 50 °C resp. -20 °C - 60 °C Protection type: IP20 Condition after return: depends on the DALI settings Max. cross wire section: up to 2,5 mm² Dimensions: Check the data sheet

DALI ROT Accessories - Rotary Knob / Cover and Adapter DALI ROT is a dimmable rotary switch including a control module for switching, dimming and setting the color or color temperature of LED luminaires. With the right accessories in the form of a cover and an adapter, DALI ROT is ideally suited for standard flush-mounted boxes and is used in combination with most switch programs. The corresponding DALI ROT control module can be found under the following link: Dimmable Rotary Switch DALI ROT - Control Module. The rotary knob or the cover is available in different versions depending on the design and color. Construction: Standard or Jung Series A Color: Black or White Specification DALI ROT Accessories: Article Number Item Name Z-86459822-C-J-W Rotary knob and cover, Jung Series A, alpine white Z-86459822-C-J-S Rotary knob and cover, Jung series A, black Z-86459822-C-0-W Rotary knob and cover, standard, white RAL9016 Z-86459822-C-0-W Rotary knob and cover, standard, black Z-86459822-A Adapter 6 mm For more information, please refer to the manufacturer's data sheet in the download tab.

AL-520-00 DALI POWER SUPPLY The AL-520-00 is a quite reliablesupply with a voltage of 230V AC and a DALI compliant output voltage of up to 250mA.The device is 36mm wide and has to be mounted on a standard DIN rail. Features AL-520-00 : Supply voltage: 230V AC 1x DALI power supply output (2 push-in contacts for DALI + and DALI -) 1x Status LED Please remember that you need one supply for each DALI line (max. 64 DALI ballasts). Technical data: DALI Number 1 Outout current Max. 240 mA(+/-5%) Output voltage Typ. 16V DC (+/- 5%) Supply   Supply voltage 230V AC (+/- 10%) Power consumption max. 5,0W / 22mA Backup integrated, not resetting Environmental conditions Operating temperature +0°C to +50°C Storage temperature -20°C to +70°C Humidity 10% to 95% rel. humidity, non condensing Protection class IP20 Demensions and weight   Weight 68 g Dimensions (in mm) 94 x 36 x 60 EMV EN 61000-4-3:2006 + A1:2007 + A2:2010 EN 61000-4-4:2012 EN 61000-4-5:2014 EN 61000-4-6:2013 EN 61000-4-11:2004 EN 55015:2013 + A1:2015 CISPR 15:2013 + IS1:2013 + IS2:2013 + A1:2015 DIN EN 61547:2010-03 VDE 0875-15-2:2010-03 EN61547:2009 IEC 61547:2009 DIN EN 61547 Ber. 1:2010-07 VDE 0875-15-2 Ber. 1:2010-07 EN 61547:2009 Ber. Zu DIN EN 61547:2010-03 Further information as well as the user and installation instructions can be found in the Download tab.

NEW! EnOcean DALI Gateway Flex in installation housing, series BL The gateway establishes an EnOcean radio connection from EnOcean buttons to your DALI luminaires. So you can control/dim your DALI lighting via EnOcean radio. Special feature: Freely configurable! The Gateway Flex can be freely programmed by the user (individual button assignments, light scenes etc.) Integrated DALI power supply for up to ten slaves (maximum output current: 20mA). Installation housing: 4x socket output 5-pin WIELAND 230V AC + DALI. Useful for existing buildings and missing DALI bus from the switching unit to the luminaire unit. Further highlights: 230V Supply voltage No configuration tool required for commissioning Internal antenna Video Tutorial: PC software BL-201-FLEX for configuring the BL-201 EnOcean DALI gateways Technical Data: DALI Master Number 1 Master Output current Max. 34mA Output voltage 16V DC (+/- 5%) Galvanic isolation yes EnOcean Master Number 1 Master (bidirectional) Transceiver TCM310 Send / Receive yes / yes Antenna Integrated     Supply voltage 230V AC / 50Hz Power consumption Typ. 1,4W, max. 2,0W Operating temperature +5°C to +50°C Storage temperature +5°C to +50°C Humidity 10% to 95%, non-condensing Compatible EnOcean wireless buttons can be found here.

BL-202-10-868 EVG FLEX, EnOcean-DALI-Controller Freely configurable DALI control via the PC tool BL-PC-FLEX-2 (not included). Conduct the DALI commissioning wirelessly and, together with switches, motion detectors and daylight sensors, simply convert the customer's requirements into a solution. The EnOcean DALI controller type BL-202-10-868 EVG FLEX offers a DALI master as well as an integrated DALI power supply for the direct connection of up to 15 slaves (out max. = 30 mA) without the need for a separate DALI power supply. In addition, an EnOcean radio transceiver is integrated. These features enable the simple and easy combination of DALI ballasts or DALI LED drivers and light switches with wireless EnOcean technology. The device is supplied with 230 V AC mains voltage. It offers freely configurable functions via the PC tool BL-PC-FLEX-2 (formerly BL-PC-FLEX) (not included). Product characteristics: 230 V AC supply voltage 1x DALI Master Integrated DALI power supply for up to 15 DALI slaves (Iout max. = 30 mA) 1x EnOcean (TCM310) Internal antenna PC configuration tool BL-PC-FLEX-2 for wireless configuration of control functions Mounting in housings or profiles Technical Data: DALI Master Number 1 Master Output current DALI max. 30 mA via integrated power supply (max. 15 slaves) Output voltage 16V DC (+/- 5%) Galvanic isolation Yes EnOcean Master Number 1 Master  Transceiver TCM310 Transmit / receive Yes / yes Antenna Integrated Frequency range used 868.0 - 868.6 MHz Maximum transmission power typ. 3 dBm @ 868.300 MHz Transmit/receive center frequency 868.3 MHz / ASK (EnOcean) Recipient category according to EN 300200 2   Environmental conditions Supply voltage 230V AC  Power consumption Typ. 1,4W, max. 2,0W Operating temperature +5°C to +50°C Storage temperature -20°C to +70°C Humidity 10% to 95%, non condensing Tests / Standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + AC:2011 +A2:2013 ETSI EG 203 367 DIN/EN 55032 EN/IEC 61000-4-2 EN/IEC 61000-4-3 EN/IEC 61000-4-4 EN/IEC 61000-4-5 EN/IEC 61000-4-6 Take further data from our download-tab.

BL-202-40-868 EVG TUNABLE WHITE, EnOcean-DALI-Controller The EnOcean DALI controller type BL-202-40-868 EVG TUNABLE WHITE offers a DALI master and a DALI power supply for the direct connection of up to 15 DALI ballasts (Iout max. 30mA) without the need for a separate DALI power supply. In addition, an EnOcean radio transceiver is integrated. These features enable the simple and easy combination of DALI ballasts or DALI LED drivers and light switches with wireless EnOcean technology. The device is supplied with 230V AC mains voltage. The BL-202-40-868 EVG TUNABLE WHITE offers a fixed function for switching, dimming and changing the colour temperature (DALI DT8) via a double rocker. Wippe A : Switching and dimming Rocker B : Changing the color temperature Up to 10 EnOcean switches can be taught to the controller at the same time. Highlights function: brightness (ON/OFF/DIM) and colour temperature (DALI DT8, TC) can be set via a double rocker switch  230 V AC supply voltage 1x DALI Master Integrated DALI power supply for up to 15 DALI slaves (Iout max. = 30 mA) 1x EnOcean (TCM310) Internal antenna Installation in housing or profiles Fixed function: switching, dimming and changing the colour temperature -(DALI DT8) via a double rocker, no addressing or PC tool required Technical data DALI Master Number 1 Master Output current DALI Max. 30mA Output voltage 16V DC (+/- 5%) Galvanic isolation Yes EnOcean Master Number 1 Master (bi-directional) Transceiver TCM310 868 MHz Transmit / receive Yes / yes Antenna Integrated Transmit/receive center frequency  868.3 MHz / ASK (EnOcean) Frequency range used 868.0-868.6 MHz Maximum transmission power typ. 3 dBm @ 868.300 MHz Recipient category according to EN 300200 2 Environmental conditions Supply voltage 230V AC / 50Hz Power consumption Typ. 1,4W, max. 2,0W Operating temperature +5°C bis +50°C Storage temperature +5°C bis +50°C Humidity 10% bis 95%, nicht kondensierend Tests / Standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + AC:2011 +A2:2013 ETSI EG 203 367 DIN/EN 55032 EN/IEC 61000-4-2 EN/IEC 61000-4-3 EN/IEC 61000-4-4 EN/IEC 61000-4-5 EN/IEC 61000-4-6

BL-202-FLEX-2 STARTERKIT The BL-202-FLEX-2 starter kit provides a quick and cost-effective introduction to the practical work with the freely configurable FLEX options of the proven BL-201 and BL-202 EnOcean DALI controllers / light controllers. The kit contains the following components (see screenshot above): BL-202-10-868 EVG FLEX, EnOcean DALI controller, #11329, 1 piece BL-PC-FLEX-2, PC software, Windows, USB stick, #11228, 1 piece Radio surface scanner pure white EnOcean, #11051, 1 piece EnOcean USB stick 868 MHz, #11227, 1 piece slotted screwdriver 0. 4 x 2. 0, #11145, 1 piece Power supply cable with Euro plug, 2,0m , #11230, 1 piece In addition to a DALI electronic ballast with an associated light, or an LED strip with a corresponding DALI driver module, everything is included in the kit that is necessary for an easy start. Piece Technical data DALI Master Number 1 Master Output current DALI Max. 30mA Output voltage 16V DC (+/- 5%) Galvanic isolation Yes EnOcean Master Number 1 Transceiver TCM310 Transmit / receive Yes / yes Antenna Integrated Transmit/receive center frequency  868.3 MHz / ASK (EnOcean) Frequency range used 868.0-868.6 MHz Maximum transmission power typ. 3 dBm @ 868.300 MHz Recipient category according to EN 300200 2 Environment conditions  Supply voltage 230V AC  Power consumption Typ. 0,8W, max. 2,0W Operating temperature +5°C to +50°C Storage temperature -20C to +70°C Humidity 10% bis 95%, nicht kondensierend Tests / Standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + AC:2011 +A2:2013 ETSI EG 203 367 DIN/EN 55032 EN/IEC 61000-4-2 EN/IEC 61000-4-3 EN/IEC 61000-4-4 EN/IEC 61000-4-5 EN/IEC 61000-4-6 For further information, please refer to the data sheet in the Download tab.

BL-204-10-868 EVG FLEX EnOcean-DALI-Controller The type BL-204-10-868 EVG FLEX offers a DALI master and an integrated DALI power supply for the direct connection of up to 15 slaves (Iout max. = 30 mA), without the need for a separate DALI power supply. In addition, an EnOcean radio transceiver is integrated. These features allow the easy and hassle-free combination of DALI ballasts or DALI LED drivers and light switches with wireless EnOcean technology. The device is supplied with 230 V AC mains voltage. The DALI bus of the BL-204-10-868 EVG FLEX can be accessed either additionally or alternatively via the AL-500-00 DALI 4-channel input module (Art. no. 12 002) up to 4x 4 = 16 wired switches or switches. buttons are read in and used locally for the control. In addition, this switching information is sent via EnOcean as RPS radio telegrams to control external actuators or to link other lighting controls. It is free configurable with our PC software BL-PC-FLEX-2, and provides the following Features: 230 V AC power supply voltage 1x DALI Master Integrated DALI power supply for up to 15 DALI Slaves (Iout max. = 30 mA) 1x EnOcean Master, bi-directional (TCM310) Internal antenna PC Configuration tool BL-PC-FLEX-2 to configure DALI and EnOcean functionality (not included) To be mounted directly into luminaires and profiles Dimensions: 144 x 21 x 18 mm New: Supports AL-500-00 DALI input module 4-channel, for wired light switches / push buttons / motion detectors etc. Remove further data from our download tab Application example AL-500-00 BL-204-10-868 EVG FLEX The following video shows the use of an AL-500-00 DALI 4-channel input module on a BL-204-10-868 EVG FLEX. The AL500-00 is connected to the DALI bus and is supplied by it. The first input A is connected with a conventional light switch. On the left side of the picture you can see the software BL-PC-FLEX-2. This has been started and the EnOcean USB stick is connected (COM field highlighted in green). If the button is now pressed, it first appears on the right in the EnOcean Explorer as "available". With a double click this is "projected". The key press corresponds to “A1.” The ON/OFF/DIM function is configured as DALI BROADCAST for the A1 key and the configuration is loaded into the EnOcean DALI controller BL-204-10-868 EVG FLEX. At the end you can see the desired functionality when you press the button. .videoHolder{max-width:1120px;max-height:630px;}.videoWrapper {max-width:1120px;position: relative;padding-bottom: 56.25% !important;height: 0;}.videoWrapper iframe {position: absolute;top: 0;left: 0;width: 100%;height: 100%;max-height:630px; max-width:1120px;} AL-500-00 with BL-204-10-868 EVG FLEX V1   Take further data from our download-tab

BL-204-FLEX-2 STARTERKIT Das BL-204-FLEX-2 Starter-Kit ermöglicht einen schnellen und kostengünstigen Einstieg in die praktische Arbeit mit den frei konfigurierbaren FLEX-Optionen der bewährten BL-201 und BL-202 EnOcean-DALI-Controller / Lichtsteuerungen. Im Kit enthalten sind folgende Komponenten (s. Abbildung oben): BL-202-10-868 EVG FLEX, EnOcean-DALI-Controller, #11329, 1 Stück BL-PC-FLEX-2, PC-Software, Windows, USB-Stick, #11228, 1 Stück Funk Flächentaster reinweiß EnOcean, #11051, 1 Stück EnOcean USB-Stick 868 MHz, #11227, 1 Stück Schlitzschraubendreher 0.4 x 2.0, #11145, 1 Stück Netzanschlussleitung mit Eurostecker, 2,0m , #11230, 1 Stück Außer einem DALI EVG mit zugehöriger Leuchte, oder einem LED-Streifen mit entsprechendem DALI Treiberbaustein, liegt somit dem Kit alles bei was für den einfachen Start erforderlich ist. Prüfungen / Standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + AC:2011 +A2:2013 ETSI EG 203 367 DIN/EN 55032 EN/IEC 61000-4-2 EN/IEC 61000-4-3 EN/IEC 61000-4-4 EN/IEC 61000-4-5 EN/IEC 61000-4-6 Entnehmen Sie weitere Daten aus unserem Download-Tab.

BL-PC-FLEX-2 SETUPKIT PC software for the configuration of the freely configurable "FLEX" lighting controllers The BL-PC-FLEX-2 Setup Kit enables practical work with the freely configurable FLEX options of the proven BL-201 and BL-202 EnOcean DALI controllers / light controllers. The kit contains the following components (see screenshot above): BL-PC-FLEX-2, PC software, Windows, on USB stick, # 12229, 1 piece EnOcean USB flash drive 868 MHz, # 11227, 1 piece Technical Data:   EnOcean Master Number 1 Master  Transceiver TCM310 Transmit / receive Yes / yes Antenna Integrated Frequency range used 868.0 - 868.6 MHz Maximum transmission power typ. 3 dBm @ 868.300 MHz Transmit/receive center frequency 868.3 MHz / ASK (EnOcean) Recipient category according to EN 300200 2   Environmental conditions Supply voltage 5V DC via USB Power consumption Typ. 0,1W Operating temperature -20°C to +50°C Storage temperature -20°C to +50°C Humidity 10% to 95%, non condensing Tests / Standards: DIN/EN 55032:2012 EN 55035:2017 EN 301489-3 EN 61000-3-2:2014 EN 61000-3-3 EN 300220-2 EN 62368-1 EN 62479000-4-5 EN/IEC 61000-4-6 For a simple overview of the functionality we recommend the following video: Video instructions for BL-PC-Flex software (#11228) for the BL-201/202 series FLEX EnOcean DALI controllers .videoHolder{max-width:1120px;max-height:630px;}.videoWrapper {max-width:1120px;position: relative;padding-bottom: 56.25% !important;height: 0;}.videoWrapper iframe {position: absolute;top: 0;left: 0;width: 100%;height: 100%;max-height:630px; max-width:1120px;} PC software BL-201-FLEX for configuring the BL-201 EnOcean DALI gateways   Video language is german.

Bridge digitalSTROM-DALI-EnOcean-hue from Plan44 This improved version 2 has an external antenna (SMA), power supply using a standard USB micro power supply or via Ethernet (with a separate PPoE kit) and is more energy efficient.By using the new digitalSTROM virtual device connector technology to seamlessly integrate new devices, they work just as easily for users as normal digitalSTROM components.The P44-DSB-DEH2 device connects up to 64 dimmable DALI lights, many radio buttons, sensors and actuators and Philips "hue" color LED lights.To expand room climate control (EnOcean), office lighting (DALI), modern LED lighting of various types (DALI, hue) and freely positionable radio light buttons (EnOcean), the P44-DSB-DEH2 is a cost-effective way to achieve this.It only needs a P44-DSB-DEH2 to connect a variety of third-party components that ideally complement the digitalSTROM components.The P44-DSB-DEH2 firmware can be updated with a simple push of a button to receive support for new devices, new features and general improvements. DALI - up to 64 dimmable lights on a 2-wire bus DALI is a proven and widespread industry standard (IEC 62386) for lighting. Up to 64 DALI "slave" devices can be connected with a two-wire bus. The bus is powered and controlled by the P44-DSB-DEH2 as a DALI "master". Unlike many DALI "master" devices, the P44-DSB-DEH2 does not require manual configuration of the DALI devices, but automatically recognizes all connected devices and makes them available as digitalSTROM-compatible devices. Compatible DALI devices are available from many manufacturers, such as Unidim, Osram, Tridonic, Meanwell, TCI, Helvar and many others.DALI control devices (e.g. presence detectors or brightness sensors) are not supported and can disrupt operation via digitalSTROM. Instead, use appropriate digitalSTROM terminals or EnOcean sensors. EnOcean - wireless self-sufficient components EnOcean is a technology for wireless, usually self-supplying ("energy harvesting") buttons, sensors and actuators.The P44-DSB-DEH2 has a built-in EnOcean radio module (TCM310) to receive data from EnOcean buttons and sensors and to transmit commands to EnOcean actuators such as heating valves. The P44-DSB-DEH2 firmware automatically recognizes the EEP (enocean equipment profile) of the component in order to integrate the various devices in digitalSTROM accordingly. For example, Sensors for climate data as blue digitalSTROM components and buttons function as light switches as standard, but can also be used for other functions. hue - coloured LED lights, wirelessly remote controlled "hue" lights are coloured LED lamps from Philips, which can be controlled wirelessly via smartphone apps or third-party software.P44-DSB-DEH2 lets "hue" lights become part of the digitalSTROM light scenes. Create your multi-coloured light scenes and simply call them up by pressing the light button. The P44-DSB-DEH2 recognizes and connects the "hue" bridge at the push of a button. Once connected, all "hue" lights appear as (yellow) digitalSTROM light components. The normal hue functionality remains unchanged, you can still control the lights with the mobile hue app, via the hue cloud or with third-party applications. The single-colour hue "lux" lights are also supported.You can find more information about this product in the download tab.

Casambi Dimmer Bluetooth Unit - dimming via app by DALI light control Compact controller to integrate a DALI-compatible LED driver in your lighting unit. Control a lamp via smartphone with Casambi Bluetooth App for the Casambi Dimmer Unit... ... to create a perfect lighting control system Through a Bluetooth connection and appropriate App you can dim your Smart Device lamps, switch individual lights on and off, create light scenes and a desired mood in your own 4 walls. Available in 4 different versions: 1 Channel (sent via DALI-Broadcast) 2 Channel (sent to DALI addresses*: 0, 1) 3 Channel RGB (sent to DALI addresses*: 0, 1, 2) 4 Channel RGBW (sent to DALI addresses*: 0, 1, 2, 3) (* DALI addresses of devices has to be programmed regarding this) Another Casambi highlight: Even with your conventional light switch you can dim and switch your lights. Conceived as backup when the phone is straight not with, or as a simple alternative, if cables for DALI are missing and you still want to dim. So you can easily adjust with Casambi reduce lights. 1. Switch on illumination with a usually switch. 2. Short off and on again withing 1 second. The illumination slowly dims up. 3. Another short off and on again at the desired dimming level. The current dimming value is stored. 4. If the second off / on is not switched between 8 seconds, will the illumination dim up to 100%. All products by Casambi family have following features: Creates automatically a wireless Mesh-Network with other Casambi products. Wireless control using the free Casambi App for smartphones and tablets. Integrate the use of regular wall switches for dimming and scene control. Support for external on / off motion sensors.   Compatible devices and minimum requirements for Casambi App: Android  iOS   min. Android 4.4 KitKat with Bluetooth 4.0  from iPhone 4S                            recommended: Android 5.0 Lollipop with Bluetooth 4.0  from iPad 3  or current Android versions  from iPod 5 These functions does the free Casambi App: Dimming of single or multiple lights with simple touch gestures. Controlling the lighting of your stores, offices, or personal spaces. Installation of single or complex scenarios with one or more lightings.   Define the security of the network. There are four different levels of security for access control. Also support Philips HUE. Casambi App free download: Casambi App Android (Google Play) Casambi App iOS (iTunes)  Specifications of Casambi CBU ASD Bluetooth Unit:  Input    Input voltage  220-240VAC (50Hz)  Max. input voltage  1.2A  Standby power  220-240VAC (50Hz)  DALI Output    Bus voltage  12VDC  Current 7mA  Radio transceiver    Frequency range  2,4-2,483 GHz  Max. output power  +4 dBm  Mechanical data    Dimensions  56.5 x 35.8 x 22.3 mm  Weight  48g  Protection  IP20  Protection class  Built-in class II   Casambi App in Appstore Casambi App for Android

Waterproof Casambi Interface for controlling DALI devices (ASD25, ASD60) This configurable Casambi module allows convenient regulation or control of multiple LED control gear with DALI signal input. This lighting control function is performed by a smart device (Apple, Android) with the Casambi app. Depending on the version of this Casambi interface, up to 25 or 60 DALI participants can be integrated into the network. Product Overview / Features: Waterproof interface for convenient control of up to 25 or 60 LED control gears with DALI signal input Configuration of the other interface types is possible before pairing to a network: change profile Casambi interface sends DALI broadcast (1Ch), 4 groups (DALI groups G0-G3), RGBW Gateway is not needed, but setup possible Integrated antenna Connection cables, 15 cm each Use the free app from CASAMBI (Apple / Android) to conveniently control all settings (downloads below in the description) Control brightness Configuring luminaires and luminaire networks Creating scenes and animations New devices are detected automatically Intelligent timer and gallery functions Set sharing options (only me, everyone, only with password, ...) Technical data: Article no. built-in housing 808893 808894 Type Built-in housing IBTPRODAC IBTXPRODA25C Power supply input 220..240 Vac; 50 Hz Alternative control None Button Radio signal 2.4..2.483 GHz; 4 dBm Signal output DALI, max. 100 mA; SELV DALI, max. 50 mA; SELV Ambient temperature -20.. +40 °C -20.. +50 °C Degree of protection IP 44 Dimensions (without cable) 38 x 38 x 26 mm 27 x 61 x 22 mm Experience the new application diversity of CASAMBI. Through Casambi, you can conveniently control your lighting via smartphone or tablet, wirelessly and easily individually. The control runs via Casambi LE (low energy). If several Casambi modules are in use, a so-called "mesh network" is built up. Each additional Casambi module increases the range, because each module establishes a direct connection to all others. Your luminaires can now not only be dimmed, switched on and off, but the timer function allows you to control the lighting according to time. A maximum of 3 lights can be combined into a group, light scenes can be stored, and much more. The compact modules are simply mounted in front of the luminaire, so there is no need to run additional cables. The setup is extremely simple, all components are automatically recognized in the network and in the app. CASAMBI QR code and links: Casambi app in the app store Casambi app for Android What CASAMBI can do! You can find many other supporting videos about Casambi at YouTube . For more information, please refer to the data sheet in the download tab.

Casambi Dimmer 2,4Ghz Radio Unit Class II - dimming via app by DALI light control Compact controller to integrate a DALI-compatible LED driver in your lighting unit. Control a lamp via smartphone with Casambi App for the Casambi Dimmer Unit... ... to create a perfect lighting control system Through a 2,4Ghz radio Connection and appropriate App you can dim your Smart Device lamps, switch individual lights on and off, create light scenes and a desired mood in your own 4 walls. Available in 4 different versions: 1 Channel (sent via DALI-Broadcast) 2 Channel (sent to DALI addresses*: 0, 1) 3 Channel RGB (sent to DALI addresses*: 0, 1, 2) 4 Channel RGBW (sent to DALI addresses*: 0, 1, 2, 3) (* DALI addresses of devices has to be programmed regarding this) Another Casambi highlight: Even with your conventional light switch you can dim and switch your lights. Conceived as backup when the phone is straight not with, or as a simple alternative, if cables for DALI are missing and you still want to dim. So you can easily adjust with Casambi reduce lights. 1. Switch on illumination with a usually switch. 2. Short off and on again withing 1 second. The illumination slowly dims up. 3. Another short off and on again at the desired dimming level. The current dimming value is stored. 4. If the second off / on is not switched between 8 seconds, will the illumination dim up to 100%. All products by Casambi family have following features: Creates automatically a wireless Mesh-Network with other Casambi products. Wireless control using the free Casambi App for smartphones and tablets. Integrate the use of regular wall switches for dimming and scene control. Support for external on / off motion sensors. Compatible devices and minimum requirements for Casambi App: Android  iOS  min. Android 4.4 KitKat from iPhone 4S recommended: Android 5.0 Lollipop from iPad 3 or current Android versions  from iPod 5 These functions does the free Casambi App: Dimming of single or multiple lights with simple touch gestures. Controlling the lighting of your stores, offices, or personal spaces. Installation of single or complex scenarios with one or more lightings.   Define the security of the network. There are four different levels of security for access control. Also support Philips HUE. Casambi App free download: Casambi App in Appstore Casambi App for Android    Specifications of Casambi CBU ASD Radio Unit:  Input    Input voltage  220-240VAC (50Hz)  Max. input voltage  1.2A  Standby power  220-240VAC (50Hz)  DALI Output    Bus voltage  12VDC  Current 7mA  Radio transceiver    Frequency range  2,4-2,483 GHz  Max. output power  +4 dBm  Mechanical data    Dimensions  56.5 x 35.8 x 22.3 mm  Weight  48g  Protection  IP20  Protection class  Built-in class II For more information please refer to the data sheet in the Download-Tab.

Casambi light control module, IP65, waterproof casing, DALI, This Casambi module provides a variety of dimming functions: DALI: CCT, RGB, RGB+W, 1..4 CH  0-10V Experience the new variety of applications of CASAMBI With Casambi you can operate your lighting easily and individually, conveniently via smartphone or tablet, wirelessly, based on Casambi. Controlling runs via Casambi LE (Low Energy). If several Casambi modules are in use, a so-called "mesh network" is built up. Each additional Casambi module increases range, because each module establishes a direct connection to all others. Your luminaires can now not only be dimmed, switched on and off, but also timed via the timer function, up to max. 3 lights can be combined to a group, light scenes deposited, and much more. The compact modules are simply mounted in front of the luminaire or behind the switch so that no additional cables need to be laid. The setup is extremely simple, all components are automatically detected in the network and in the app. This device with IP 65 protection can be used wherever you have to reckon with moisture during use, for example: Bath rooms Sauna areas Swimming baths Coolings houses Garden lights For all outdoor applications Convenient control of all settings via the free App from CASAMBI (in the text below): Adjustment of brightness (dimming) and light temperature Configuration of luminaires and lighting networks (Groups) Creating scenes and animations (Colour gradients) New devices are detected automatically Smart timer and gallery functions Protection settings of your network (only me, all, only with password,...) Compatible with Apple Watch Also controllable via power switch or wall switch RWBT XPress and EBT, (to be found directly in the tab Recommendations) Other special features: Fixed rubber connection cables, 15 cm each Interface with IP 65 protection for convenient control of LED power supplies with DALI input signal by smartphone or tablet (Apple/ Android) via Casambi Sends DALI broadcast. Possibility to configure the other interface types I (U) BTU, I (U) .. BTDA before pairing with the network: Change profile You can also setup a gateway but it is no necessary Integrated antenna (see position drawings, gray area, do not cover with metal casing) Switched network output: To avoid standby currents and to switch off the connected lighting at 0% dimming via the Casambi App completely, a relay suitable for the power to be switched must be used. A corresponding circuit diagram can be found in the Tab images. We offer the suitable relay directly in the recommendation tab. Location of the antenna When installing, pay attention to the position of the antenna and avoid larger metallic structures or, if necessary, plan a recess for the antenna. It is recommended to test the range after all conversions. The position and size of the recess can be found in the image in the Images tab. Technical data:   Article no. built in housing 808685 Type built in housing IIBTPRO Power supply input 220..240V; 50 Hz Signal Input Casambi 4.0 lite @ smart devices Radio signal 2,4..2,483 GHz; 4 dBm Signal output DALI / 0-10V, max. 7 mA; SELV; short circuit protection Ambient temperature (ta) -20.. +40 °C Rated max. temp. (tc) 70 °C IP Protection level 65 Dimensions 100 x 37 mm (without cable) CASAMBI QR-Code and Links (direct download) Casambi App in the Appstore Casambi App for Android .videoHolder{max-width:1120px;max-height:630px;}.videoWrapper {max-width:1120px;position: relative;padding-bottom: 56.25% !important;height: 0;}.videoWrapper iframe {position: absolute;top: 0;left: 0;width: 100%;height: 100%;max-height:630px; max-width:1120px;} CBU-ASD modules, control of lighting with 3 wires and dimming More supportive videos about Casambi can be found on YouTube. For further information and wiring diagrams please refer to the data sheet. (Download-Tab)

Casambi bluetooth control unit CBU-A2D - Control two devices with 0-10V or DALI via Bluetooth Features of the Casambi CBU A2D The CBU-A2D is a casambi bluetooth control unit with 2-channel 0-10V / DALI . The module is operated over a universal input voltage range of 100-277 VAC. The CBU-A2D enables the control of two LED drivers with 0-10V or DALI input. Alternatively, the tuneable white control with two independent LED drivers for warm white / cold white is also possible.The product can also be configured as a DALI push-button interface, where it can be connected for presence and / or daylight use functions. The CBU-A2D can be controlled and configured using the Casambi app. Various Casambi-capable products can be used, from a simple direct control of a luminaire to a complete and full lighting control system, in which up to 250 units automatically form an intelligent mesh network. Technical facts about the Casambi A2D Voltage range 100-240 (CE/UL/CSA)277 VAC (only UL/CSA) Frequency 50-60 Hz Max. main current 35 mA No-load standby power <0,5 W Channel 1 output Output voltage, 0-10V, 0-10 VDC, max. 7 mA (sinking)Output voltage, DALI 12 VDCmax. 20 mA (sourcing)Maximum number of drivers: 1  Channel 2 output Output voltage, 0-10V: 0-10 VDC, max7mA (sinking)Output voltage, relay control: 12 VDC,max. 100 mA (sourcing)Maximum number of drivers: 1 Dimensions 76,0 x 26,0 x 23,0 mm3.0 x 1.0 x 0.9 Zoll Protection IP20Built-in class II

CBU-DCS DALI Casambi Gateway and DALI Controller Core functions: Integration of Casambi luminaires into a DALI network. Control DALI luminaires via broadcast via Casambi app CBU-DCS supports DALI-2 input devices and can be connected to a DALI sensor for presence detection or daylight harvesting, or to a DALI pushbutton interface for manual control. CBU-DCS can be connected to wired DALI controllers where it acts as a wireless DALI gateway into the Casambi mesh, either in DALI broadcast mode or for controlling individually addressed DALI devices. CBU-DCS is protected against overvoltage, overcurrent and short circuit. The Casambi system can be controlled via smartphone or tablet using the Casambi app, which can be downloaded for free from the Apple App Store and Google Play Store. It can also be controlled using timers, Casambi-enabled sensors such as passive infrared (PIR) presence detectors and lux sensors, as well as Casambi Xpress and EnOcean switches. An external gateway module is not required. In short: 19 different profiles can be loaded into the CBU-DCS via the Casambi app. Profiles can be loaded. Thus, it offers a wide range of application possibilities. Popularly used are these functions of the DALI Casambi Gateway: DALI Gateway allows Casambi luminaires or devices to be transparently integrated into the DALI network and controlled via it. --> Select profile CBU-DCS-DALI, connect CBU-DCS to DALI bus, connect all luminaires incl. CBU-DCS into the same Casambi network. Final then search for new devices via DALI. The Casambi luminaires are then shown as virtual DALI addresses in the DALI network and can be controlled via them, identically to hardwired ones.   DALI Broadcast enables commands sent via Casambifunk to be sent to all DALI addresses. --> Select profile CBU-DCS-Broadcast, connect CBU-DCS to DALI bus, and after establishing a connection via Casambi all luminaires connected to the DALI bus can be controlled via broadcast. Technical data CBU-DCS: Input   Voltage range 9,5-22,5 VDC Idle input current 5 mA Peak input current 30 mA Max. DALI bus current 250 mA Standby power < 0,1 W Radio transceiver   Operating frequencies 2,4-2,483 Ghz Max. Output power +4dBm Operating conditions   Ambient temperature, ta -20...+55°C Max. housing temperature, tc +65°C Storage temperature -25...+75°C Max rel. humidity 0...80%, not condensing Connectors   Wire range 0,5 - 1,5 mm2, 16 - 20 AWG Length of the wire strip 6 - 8 mm   Dimensions 40,4 x 36,3 x 14,0 mm Weight 15 g Protection type IP20 (only indoor)   Here you can download the app for free: Casambi App Appstore Casambi App for Android For more information, please refer to the data sheet in the download tab. An example of an explanatory video for using the module as DALI according to Casambi Gateway.